Shaft Couplings — Match the Torque, the Bores and the Misalignment

What a Coupling Actually Has to Do

A shaft coupling joins two rotating shafts so torque passes from the driver to the driven machine. That sounds simple until you account for the fact that two machines bolted to a base plate are never perfectly aligned, and that starting, stopping and reversing send shock through the joint. A flexible coupling absorbs small angular, radial and axial misalignment and damps torsional vibration; a rigid coupling transmits torque with zero backlash but demands that the two shafts be aligned almost perfectly. Choosing between them is a torque-and-alignment decision, not a catalogue decision. We supply the common industrial types from audited partner factories, machine the bore and keyway to your drawing at the partner workshop, and ship the coupling with the bore, keyway and balance record on the inspection report.

Choose the Type by What It Tolerates

Coupling types, what each tolerates and what to confirm before ordering.
TypeWhat it toleratesWhere it is usedWhat to confirm
Jaw coupling with elastomer spiderSmall angular and radial misalignment; damps vibration; the elastomer is the wear partPumps, fans, compressors, conveyors, general drivesSpider hardness, torque at start-up, temperature limit of the elastomer
Disc coupling (single or double disc)Angular and axial misalignment with very low backlash and high torsional stiffnessServo axes, CNC, test rigs, high-speed drivesSingle vs double disc (only the double disc handles parallel offset), disc material, speed
Pin-and-bush (elastic pin) couplingModerate misalignment and shock; simple to serviceCrushers, mixers, hoists, heavy starting loadsPin and bush material, number of pins, brake or reversing duty
Rigid coupling (sleeve or clamp)No misalignment at all; zero backlash, highest stiffnessShort aligned shafts, vertical pumps, precision spindlesBore fit, clamping method, shaft alignment tolerance
Gear / grid / bellows / OldhamHigher torque, or very low backlash at small offsets, depending on typeSteel mills, large pumps, encoders, light instrumentationLubrication needs, backlash requirement, axial travel

Six Values to Send With Every Coupling RFQ

Give the transmitted torque and the peak or starting torque, not just the motor power — a coupling that survives running torque can fail on the first start under load. State the speed, both shaft diameters (d1 and d2, which are often different), the bore fit and the keyway or clamping method, and the misalignment you expect: angular, radial (parallel offset) and axial, each separately. Add the direction of rotation and whether the drive reverses or brakes, since reversing changes the spider or disc specification. Tell us the environment (oil, dust, washdown, temperature), any backlash or torsional-stiffness requirement for a servo axis, and the space available — the overall length and outside diameter are often fixed by the guard. If you have a drawing of the two shaft ends, send it; we machine the bores to that drawing at the partner workshop and record both bore sizes on the inspection report.

Where These Couplings Are Fitted

Water and wastewater pumps, centrifugal fans and blowers, air and refrigeration compressors, belt and screw conveyors, mixers and agitators, hoists and winches, packaging and printing machines, machine tool and servo axes, agricultural drive lines, and generator or test-rig setups. In each case the coupling is sized on starting torque and the misalignment that appears after the base plate settles — not on the nominal motor rating alone.

Coupling Types We Quote Most Often

Jaw coupling, 24 / 28 mm bores, elastomer spider — placeholder illustration

Jaw coupling, 24 / 28 mm bores, elastomer spider

  • Bore d124 mm
  • Bore d228 mm
  • SpiderNBR
  • KeywaysYes
[PLACEHOLDER]
Jaw coupling, 38 / 42 mm bores, clamp hubs — placeholder illustration

Jaw coupling, 38 / 42 mm bores, clamp hubs

  • Bore d138 mm
  • Bore d242 mm
  • HubsClamp type
  • SpiderHigh-torque
[PLACEHOLDER]
Double disc coupling, 20 / 25 mm bores, low backlash — placeholder illustration

Double disc coupling, 20 / 25 mm bores, low backlash

  • Bore d120 mm
  • Bore d225 mm
  • DiscDouble
  • DutyServo
[PLACEHOLDER]
Pin-and-bush coupling, 55 / 60 mm bores — placeholder illustration

Pin-and-bush coupling, 55 / 60 mm bores

  • Bore d155 mm
  • Bore d260 mm
  • Pins8
  • DutyHeavy start
[PLACEHOLDER]
Rigid clamp coupling, 30 / 30 mm bores — placeholder illustration

Rigid clamp coupling, 30 / 30 mm bores

  • Bore d130 mm
  • Bore d230 mm
  • TypeClamp
  • BacklashZero
[PLACEHOLDER]

Request a Quote for Shaft Couplings

Give the torque, both shaft diameters and the misalignment you expect — we quote the coupling with the bore and keyway machined to your drawing.