Linear Guide Blocks — Series, Mounting Pattern and Preload

The Block Sets Stiffness, the Rail Sets Straightness

A linear guide block is a carriage with recirculating balls or rollers that runs on a profiled rail. Inside it, the rolling elements leave the load-carrying raceway at one end, return through a channel and re-enter at the other end, which is what allows unlimited travel on a finite rail. The block carries the carriage, sets the preload, and decides how much moment load the axis can take; the rail sets the straightness. Two details catch buyers out. First, a block is specified by its series and mounting pattern, not just by the rail width — a square type and a flanged type for the same series have different hole positions and heights. Second, preload is a purchase decision: a light-preload block runs freely on a general handling axis, while a medium or heavy preload stiffens a machining axis but raises friction and heat. We quote rails and blocks as a matched set from the same lot at the partner factory.

Square, Flanged and Everything Else

Block variants — mounting pattern, preload and accuracy grade are confirmed on the quotation.
VariantWhat differsChoose it when
Square typeLower profile, tapped or through mounting holes from the topLimited height, a carriage plate bolted from above
Flanged typeWider flange with four mounting holes, higher moment capacityCantilevered carriages, gantry axes, heavy side loads
Standard / long / short lengthNumber of rolling elements in the load zoneLong type for higher load and stiffness; short type for a compact envelope
Light / medium / heavy preloadInternal interference between rolling elements and racewaysLight for smooth general motion; medium or heavy for machining stiffness
Ball type / roller typeRolling element formBall for speed and low friction; roller for stiffness and load
Standard, high or precision accuracy gradeHeight and running parallelism variation within a setMatch the grade to the axis accuracy and the rail grade on the same order
End seals, scrapers, lubrication fittingsContamination control and grease accessCoolant and chips, dust, or a lubrication line from either end

What to Measure on the Old Block

Give the series (15 / 20 / 25 / 30), the block type (square or flanged, standard / long / short), the mounting hole pattern and thread, and the overall assembly height from the rail base to the carriage face. State the preload class and the accuracy grade, the load on each block in the vertical, lateral and moment directions, the speed and duty cycle, and the lubrication method and which end the grease fitting must face. Add the environment — coolant, chips, dust, washdown, clean room — because it decides the end seal and scraper specification, and say how many blocks sit on each rail. For a replacement, measure the four mounting holes centre-to-centre and photograph the block from above and from the end. If the axis uses two rails, tell us whether only one block is being replaced: mixing a new block with worn blocks on the same carriage changes the load sharing, and we will quote the set instead.

Standard Series Compatibility

Our blocks are supplied to standard 15 / 20 / 25 / 30 series dimensions. A block specified for a given series is compatible with standard 15 / 20 / 25 / 30 series rails of the same series, accuracy class and preload. Where your existing axis uses a different numbering system, we cross-match the block to the rail by the rail width, the hole pitch, the block mounting pattern and the assembly height, and we cross-reference those four measurements to the correct series. Parts described as interchangeable with standard series are matched on those dimensions and on the preload class, not on a name.

We state interchangeability only as standard series compatibility. We do not claim any brand authorization, and we do not list third-party brand names as our own products. Send the four measurements and a photo of the mounting face with your RFQ and we will confirm the fit before quoting.

Where Blocks Are Replaced and Specified

CNC machining centres, laser cutters and gantry robots, automated assembly and pick-and-place axes, packaging and labelling machines, semiconductor and inspection equipment, 3D printers, woodworking machines, and medical automation. The most common enquiry is a single worn carriage on an otherwise sound axis; the second is a new axis where the block and rail have to be ordered together. Both are sized from the same four measurements.

Replacing One Worn Carriage

Measure the mounting hole pattern, the block width and length, the overall assembly height and the rail width, and photograph the end face so we can identify the seal and grease fitting. We cross-reference those values to the standard series and confirm the type and preload in the first reply. Tell us how the old block failed: brinelling or a rough spot usually points to contamination or a lost preload, while a loosened carriage points to mounting bolt torque. If more than one block shares the carriage, we recommend quoting the set from one lot at the partner factory so the height and preload match across all of them.

Matching Rails

A block is only half the axis. Order the rail in the same series, accuracy class and preload, cut to your travel length with the hole pitch you specify; cutting and end machining are handled by our partner workshops. We ship the matched set from one lot with the series, length and preload on one packing list.

Linear Guide Block Models

Square block for 25-series rail — placeholder illustration

Square block for 25-series rail

  • Series25
  • TypeSquare
  • GradeStandard
[PLACEHOLDER]
Square block for 15-series rail — placeholder illustration

Square block for 15-series rail

  • Series15
  • TypeSquare
  • PreloadLight
[PLACEHOLDER]
Square block for 20-series rail — placeholder illustration

Square block for 20-series rail

  • Series20
  • TypeSquare
  • GradeStandard
[PLACEHOLDER]
Flanged block for 20-series rail — placeholder illustration

Flanged block for 20-series rail

  • Series20
  • TypeFlanged
  • PreloadMedium
[PLACEHOLDER]
Long square block for 25-series rail — placeholder illustration

Long square block for 25-series rail

  • Series25
  • TypeLong square
  • LoadHigh
[PLACEHOLDER]
Flanged block for 25-series rail, sealed — placeholder illustration

Flanged block for 25-series rail, sealed

  • Series25
  • TypeFlanged
  • SealEnd seals and scrapers
[PLACEHOLDER]
Square block for 30-series rail, heavy preload — placeholder illustration

Square block for 30-series rail, heavy preload

  • Series30
  • TypeSquare
  • PreloadHeavy
[PLACEHOLDER]
Roller-type block for 25-series rail — placeholder illustration

Roller-type block for 25-series rail

  • Series25
  • TypeRoller
  • StiffnessHigh
[PLACEHOLDER]
Precision-grade block for 25-series rail — placeholder illustration

Precision-grade block for 25-series rail

  • Series25
  • GradePrecision
  • SetMatched
[PLACEHOLDER]

Linear Guide Block Questions

Can I replace just one block, or do I need the set?

A single block can be replaced if the others are still within tolerance and the preload class matches. Send the mounting pattern, assembly height and a photo of the end face. If several blocks share one carriage, we recommend quoting the set from the same lot so their heights and preloads match.

Square or flanged — which one do I have?

A square block has a lower profile and mounting holes through the top; a flanged block has a wider base with four holes and handles higher moment loads. Measure the hole spacing and the overall width, or send a top-view photo, and we will confirm the type before quoting.

What does preload change?

Preload sets stiffness and friction. Light preload suits smooth general motion; medium or heavy preload stiffens a machining axis but raises drive force and heat. Tell us the preload class on the existing block — or the stiffness you need — and we will quote the matching rail and block from one lot.

Request a Quote for Linear Guide Blocks

Send the bore, outside diameter, width and the duty in one RFQ. We confirm the fit before quoting and state MOQ, lead time and Incoterms.