Oil Seals — Four Dimensions Decide the Seal

A Seal Is Specified by the Medium, Not by the Part Number

An oil seal holds lubricant in and keeps dirt, water and dust out of a rotating shaft. Most industrial enquiries are for the TC type — a double-lip seal with a metal case, a garter spring on the primary lip and a secondary dust lip — but the profile is only half the decision. The shaft diameter, housing bore and width set the fit; the medium, temperature, shaft speed and shaft surface decide the lip material. A seal that fits perfectly will still fail in weeks if the lip material cannot take the fluid or the shaft is rough enough to cut it. We supply TC and related profiles from audited partner factories, with lip diameter and spring tension checked at pre-shipment inspection and the results recorded against the lot.

TC Double-Lip Oil Seals

Back to top of this page

A TC oil seal has a rubber-covered metal case, a spring-loaded primary lip that retains the lubricant, and a second, unloaded lip that points outward to exclude dust and water. The garter spring keeps a constant radial force on the primary lip as it wears, and a thin film of oil under the lip is what actually does the sealing — a completely dry lip runs hot and fails. That is why these seals are standard on hydraulic pumps and motors, gearboxes and reducers, electric motors, wheel hubs, agricultural gearboxes, washing and conveying equipment, and any horizontal or vertical shaft where oil or grease must stay inside a housing. Related single-lip and pressure-rated profiles are used where there is no external contamination or where the housing sees positive pressure.

Four dimensions fix the fit: shaft diameter, housing bore, width, and the direction the seal faces during assembly. Give those first, then the medium being sealed (mineral oil, synthetic oil, grease, water, coolant), the continuous and peak temperature, the shaft speed, and any pressure in the housing. The shaft matters as much as the seal: state the surface hardness, roughness, runout and whether the shaft has a keyway, splines or a shoulder that the lip must pass over during fitting. Choose the lip material from the duty — NBR for mineral oils and greases at moderate temperature, FKM for higher temperatures and aggressive fluids, PTFE for high speed, dry running or chemical service — and tell us the case and spring material if the environment is corrosive or a washdown is routine. Include the housing bore tolerance and the lead-in chamfer; a seal driven in against a sharp edge is damaged before the machine starts. We check lip diameter and spring tension at pre-shipment inspection and ship the dimensional inspection report and material certificate with the batch, so your incoming QC has a reference before the cartons are opened.

TC double-lip oil seal, 25 × 52 × 7 mm, NBR — placeholder illustration

TC double-lip oil seal, 25 × 52 × 7 mm, NBR

  • Shaft diameter25 mm
  • Housing bore52 mm
  • Width7 mm
  • ProfileTC double-lip
  • MaterialNBR
[PLACEHOLDER]
TC double-lip oil seal, 40 × 62 × 8 mm, FKM — placeholder illustration

TC double-lip oil seal, 40 × 62 × 8 mm, FKM

  • Shaft diameter40 mm
  • Housing bore62 mm
  • Width8 mm
  • ProfileTC double-lip
  • MaterialFKM
[PLACEHOLDER]
TC double-lip oil seal, 50 × 72 × 10 mm, PTFE — placeholder illustration

TC double-lip oil seal, 50 × 72 × 10 mm, PTFE

  • Shaft diameter50 mm
  • Housing bore72 mm
  • Width10 mm
  • ProfileTC double-lip
  • MaterialPTFE
[PLACEHOLDER]

Measure These Before You Send the RFQ

Measure the shaft with a caliper at the lip contact area, the housing bore, and the seal width. Note which way the lip faces, photograph the marking on the old seal if it is still legible, and write down the medium and temperature. Add the shaft speed and the quantity. If you have no part number at all, those four dimensions plus the medium are enough for us to identify the profile and quote it.

Request a Quote for Oil Seals

Send the dimensions, the quantity and the destination port in one RFQ. We reply with price, MOQ, lead time and Incoterms.